How to Replace a Kia Sportage Replacement Key
The key in many Kia models has an electronic keyless entry system built in. The key functions like remote controls and can be exchanged with a Kia dealer.
Key fobs might stop working due to a variety of reasons, including a dead coin battery, worn buttons signal interference, water damage and a damaged receiver module. Here are some helpful tips to assist you in getting your Kia sportage replacement key working once more.
How to replace the remote key or smartkey
Whether your Kia comes with an intelligent key, remote key, push-to-start key, or regular metal non-transponder key, the battery in these keys will eventually require replacing. This is particularly true if your car shows a message that states the remote or smart keys have low battery power.
Luckily, it's a relatively simple process. In order to replace the battery on the key fob remove the mechanical key from the slit at the back of the key fob and remove the cover. Inside the key fob will be the small screw that holds the battery in the correct position. By using a small screwdriver remove the screw and remove the old battery. Install the new battery and then close the opening on the key fob.
When the key fob is equipped with a fresh battery check it by pressing the lock and unlock buttons. It's okay when the doors lock or unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or you have to complete errands in Brandon.
Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your key has to be programmed, you will need to be aware of the key code number stamped on the key code tag and save it in a safe place.
How do I replace a battery
If your Kia key fob is not responding to pressing the lock or unlock button on the fob, it is a clear indication that the battery needs to be replaced. A low battery may also cause other issues such as the check engine light coming on or delayed cranking of the engine. Fortunately, replacing the key fob battery is a relatively simple DIY project that requires only a few basic tools.
Before you begin ensure that your vehicle is off and that all doors are closed. Locate the small metal or plastic piece that is on the bottom of your key fob and gently jiggle it until the metal key slides out. The key can be put into the door's driver handle to unlock your car.
To replace the battery inside the key fob remove the cover at the rear. Utilize a plastic plier tool to open the latch that holds the black negative cable. Remove the old battery and align the new battery so that the "+" positive side is facing your face and the "negative" negative side is facing towards the fob's metallic electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.
After the new battery has been installed, turn the key fob off and then on in the ignition several times until the door locks. You can then test your Kia's keys fob to ensure it's functioning properly.
How do I replace a smart key
You may have either a standard keyfob, or a Smart Key based on the model of Kia Sportage. The smart key features an embedded mechanical key blade while the standard key fob does not. Both types of key fobs have batteries inside that will eventually have to be replaced. This is a simple procedure that takes less than two minutes.
Make sure you turn off your Kia, and be on a level well-lit and well-lit area before you begin. Keep in mind that the fob contains tiny pieces that could be thrown off in the event of a mishap.
The small release button is located on the lower backside. It will be a circular or rectangular slot. When you press it mechanical key blade, it will be released and you can then open the key fob.
Once you have the key fob open then you can remove the old battery, and replace it. The new battery is a CR-2032 that can be bought online or from your local auto parts store. When you are done with the battery, you should be able to lock or unlock your vehicle using your key fob even if the engine isn't running!
How do you replace a broken mechanical key
The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car with just pressing one button. But like any device there are issues with it at times. There are ways to solve these issues and keep your key fobs working for an extended period of time.
A dead or drained battery is among the most frequently encountered issues. kia ceed replacement key The Keylab can cause the fob to stop working altogether or work intermittently. If this is the case you should replace the battery with a fresh new one.
If this isn't enough to resolve the problem then try using a normal flathead screwdriver to open the fob's plastic casing. Be careful not to scratch any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a new one.
Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to ensure it's functioning correctly. Contact a dealer locksmith to fix the issue if the fob is still not working. Make sure they cut you an emergency key that functions across all door and trunk cylinders to avoid lockouts in the future.